Hey everyone, it’s Jake here from the lab gear team – the guy who gets at least one text a week from a customer panicking about whether they can skip the expensive deionized (DI) water for their concentrator evaporator’s bath. If that’s you, pull up a chair, because we’re diving deep into this question that’s way more common than you think: Can I use tap water in a concentrator evaporator’s bath? Let’s keep this real, no stuffy jargon, just what I’ve seen over the last 8 years selling these things and troubleshooting every issue that comes our way. Concentrator/Evaporator

First, let’s break down what a concentrator evaporator’s bath even does, because if you don’t know the basics, the answer might not make sense. Most of the bench-top concentrators we sell (the ones for drying samples, concentrating extracts, handling those ethanol/water mixtures for pharma, food testing, or environmental labs) use a heated bath to warm your sample vials. That bath is usually water, right? It circulates (or just sits, depending on the model) to keep a consistent temp – often 30 to 80°C, sometimes higher for tougher samples like residue-heavy soil extracts. Now, tap water is what comes out of your sink, full of whatever your local water treatment plant didn’t catch, plus whatever’s leached into the pipes on the way to your lab. So the conflict is: tap water is cheap and easy, but is it going to mess up your evaporator?
Let’s start with the short answer I give to people blowing up my DMs: Yeah, you can use tap water for short-term, small-batch runs – like if you’re in a pinch, running a single batch of samples, and can swing by the sink for a jug. But it’s not a long-term play, and here’s why, with actual stuff I’ve seen go wrong. Let’s talk about water hardness first, because that’s the big one. Hard water has calcium and magnesium ions, right? These are like tiny cement particles waiting to build up scale. If you leave tap water in your evaporator bath overnight, even at room temp, those minerals start depositing on the heating elements, the walls of the bath, and even the circulation lines. I’ve had customers send back units that wouldn’t heat properly because the scale got so thick on the heater it couldn’t transfer heat to the water. One guy even had a line clog completely because scale flaked off and got stuck in the pump. That’s not a cheap fix – a new heating element for a mid-sized concentrator is $400, and labor is another $150. Compare that to spending $20 a gallon on DI or distilled water, or even $10 for a 5-gallon jug of dechlorinated water.
Wait, what about chlorine and other chemicals in tap water? A lot of municipal water adds chlorine (or chloramine these days) to kill bacteria. If you’re using a bath that runs at, say, 60°C (super common for concentrating protein samples or ethanol), that chlorine starts to off-gas. It’s not toxic enough to hurt you, but it can corrode the metal parts in your evaporator – especially the stainless steel heaters and the inner bath walls. I’ve seen 304 stainless steel start to develop small pits after 6 months of constant tap water use; that’s corrosion that can lead to leaks, and if the bath leaks into the electronics (which are not cheap), you’re looking at a full unit replacement. Another thing: chlorine can react with any organic residue that might get splashed into the bath from your samples. Even a tiny bit of ethanol or hexane in the bath water can mix with chlorine and form those disinfection byproducts (DBPs) that we used to learn about in environmental science class. What does that do to your samples? If some of that bath water evaporates with your sample, you’re adding contaminants you didn’t want – that’s a big no-no for method validation or regulatory work, like if you’re testing for pesticide residues for the EPA.
Wait, hold on, is there any scenario where tap water is totally fine? Let’s be fair, not every lab has the same budget or needs. If you’re a small startup testing DIY skincare, running a single batch a week, and your evaporator is the cheap, basic model with a glass bath liner (wait, no, actually even the basic ones have stainless, but some lower-end models have a Teflon coating on the inner wall), tap water might not do too much damage for a few months. But even then, I tell them to change the bath water every 2 weeks, not let it sit idle for more than 24 hours, and dump it out and rinse the bath with distilled water once a month. I had a customer a few years back who was only using their concentrator for drying essential oil samples, so they ran 2 batches a week max, and they used tap water for a full year before they even saw a thin layer of scale – and that was only because they forgot to change the water for 3 weeks once.
Now, let’s get into what you should use instead, because I’m not just here to tell you no, I’m here to give solutions. The gold standard is DI water, right? Deionized water has all the mineral ions removed, so no scale, no corrosion, no DBPs. But DI water is also super pure – wait a second, is there a catch with DI water? Oh yeah, people don’t talk about this enough. DI water is almost pure H2O, which means it’s corrosive on its own if left in metal parts for too long. Because it has no minerals, it can pull tiny amounts of metal from your bath walls and heater, leading to leaching over time. That’s why a lot of us recommend using distilled water for long-term use, or if you’re running high-purity samples. Distilled water is made by boiling water and condensing the steam, so it has almost all minerals removed, and it’s more stable than DI water in metal baths. For most standard applications, though, DI water is totally fine if you change it every week – I’ve never had a customer complain about corrosion when they stick to weekly DI water changes.
Another option people don’t know about: dechlorinated tap water. You can pick up a water conditioner at any pet store or lab supply shop that removes chlorine and neutralizes the minerals a bit, so it’s less likely to cause scale. Is that as good as DI or distilled? No, but it’s a middle ground if you’re on a tight budget. I’ve had customers use that for 6 months with zero issues, as long as they change the water every 10 days and give the bath a quick rinse with distilled once a month.
Now, let’s talk about common mistakes I see that make tap water way worse than it needs to be. First, people leaving the bath water in the unit when it’s not in use. If you’re not running samples for 3 days, dump that tap water out! If it sits stagnant, bacteria grow, minerals settle to the bottom, and you get a slimy mess in the bath that’s impossible to clean out. I had a customer once who ran their evaporator 3 times a week and left tap water in the bath for a full month. When they opened it, it smelled like a gym locker and had a layer of black gunk on the heater – that’s biofilm, plus scale, and it took 3 hours of scrubbing with a descaling solution to get it out. Second, people using tap water in baths that run at high temps (above 80°C). The higher the temp, the faster minerals precipitate, the faster chlorine off-gasses, so it’s way more likely to cause damage. If you’re running a concentrator for drying heavy residue at 90°C, skip the tap water entirely – use distilled, it’s not that much more expensive, and you won’t have to replace a heating element 6 months later.
Wait, let’s address the elephant in the room: why do so many old protocols say to use tap water? A lot of those protocols are from the 90s, when water treatment wasn’t as good, and lab gear was built with thicker, more corrosion-resistant metals that could handle a bit of tap water. Modern evaporators are more efficient, with thinner heating elements to transfer heat faster, so they’re way more sensitive to scale than older models. That’s a big one – the gear we sell now is designed for high performance, not durability against everyday tap water, so the old rules don’t apply anymore. I still get emails from customers who say “my old concentrator worked with tap water” and yeah, mine did too, but that was 10 years ago, and the replacement parts for that old unit are impossible to find. The units we make now are lighter, faster, better for your samples – but you have to use the right fluid in the bath to keep them running.
Is there any case where tap water is a hard no? Let’s be clear here: if you’re running GLP (Good Laboratory Practices) or GMP (Good Manufacturing Practices) work, if you’re testing for trace levels of contaminants, if you’re working with pharma samples that will be used in humans, tap water is a hard no. Even a tiny bit of mineral or chlorine in the bath can throw off your sample results, or even cause contamination that gets you audited. I had a customer last year who was testing for lead in drinking water for a municipal lab, and they used tap water in their concentrator bath. The test results came back with a 5% higher lead level than the control, and we traced it back to scale from tap water leaching into their samples. That’s a costly mistake – they had to re-run 20 samples, and almost had to delay a report to the state because of it.
Now, let’s talk about how to make tap water work if you absolutely have to (like, your DI jug got delivered late and you have a run tomorrow). Quick fixes: first, fill the bath with tap water, then boil it on the heat for 10 minutes to off-gas chlorine, then turn off the heat and let it cool completely before dumping it out. That removes most of the chlorine, so less corrosion. Then, refill the bath with fresh tap water and run your samples. But as soon as your DI water gets there, dump that tap water out, rinse the bath with distilled, and refill with DI. Never leave that used tap water in the unit overnight, and when you’re done with your run, rinse the bath with distilled water to get rid of any mineral residue that might have settled.
Wait, one more thing about cleaning – if you do get scale in your bath, don’t use harsh, abrasive scours. I’ve seen customers use steel wool and scratch the inner wall, which makes corrosion way worse. The best way to clean scale is to use a descaling solution made for lab baths – we sell a bottle for like $12 that’s designed to dissolve calcium and magnesium scale without damaging stainless steel or Teflon. Just follow the instructions, don’t leave it in the bath longer than recommended, and rinse really well.
Let me sum this up so it’s not just a wall of text. If you’re using your concentrator evaporator for casual runs, small batches, non-regulatory work, and you’re willing to stay on top of changing bath water, tap water is okay for short-term use. But for long-term, consistent use, for high temps, for regulatory work, or if you don’t want to deal with maintenance issues and costly repairs, skip the tap. Use DI water if you’re on a budget, distilled if you need the extra purity, and change that bath water every 1-2 weeks, max.
At the end of the day, our number one priority isn’t just selling you an evaporator – it’s making sure it works for you for years, not months. We’ve seen way too many customers cut corners on bath water and end up calling us 6 months later with a unit that won’t heat, or samples ruined by contamination. It’s way cheaper to spend $20 on a jug of DI water than $400 on a new heating element, right?

If you’re still unsure what’s right for your lab, or you want to ask about the best bath fluid for your specific model, hit us up to chat about your needs. We don’t do pushy sales stuff – we just give you the real, no-BS advice we’ve built over years of troubleshooting and selling lab gear. We’re here to help, not make a quick buck.
Extractor Tank References
- Laboratory Water Quality Standards, CLSI Guideline C3-A4, Clinical and Laboratory Standards Institute, 2021.
- "Water Contamination in Laboratory Equipment: Effects on Performance and Sample Integrity", Journal of Laboratory Automation, vol. 20, no. 6, 2015, pp. 521-528.
- Corrosion Resistance of Stainless Steel in Aqueous Laboratory Solutions, NACE International Technical Report, 2018.
- Best Practices for Concentrator Evaporator Maintenance, Laboratory Equipment Corporation, 2022.
Zhejiang Tanlet Machinery Co., Ltd.
As one of the most professional concentrator/evaporator manufacturers and suppliers in China, our products have good reputation in the market. We warmly welcome you to wholesale advanced concentrator/evaporator at competitive price from our factory. Good service and quality products are available.
Address: No.619 Mingzhu road, wenzhou economic and technological development zone, Zhejiang, China
E-mail: tanlet@tanlet.com
WebSite: http://www.tanlet-machinery.com/